qitech-control/docs/developer-docs/Wago-Stepper-Documentation.md

Wago Stepper Controller - Developer Documentation

Models: 750-671 & 750-672
Last Updated: February 2026

Table of Contents

1. Overview
2. Hardware Quick Reference
3. Architecture & Code Organization
4. Control & Status Bytes
5. Implementation Details
6. Prescalers & Calculations
7. Common Pitfalls & Debug Tips

---

Overview

The Wago Stepper Controllers (750-671 and 750-672) drive stepper motors via EtherCAT. This documentation focuses on velocity/speed control mode implementation.

Key Differences Between Models

Feature	750-671	750-672
Max Voltage	50 VDC	70 VDC
Max Current	5 A	7.5 A
Speed Control	Via Application Selector in config	Via Control Byte C1 command
Control Byte C1	Different bit layout (M_Speed_Control bit)	Command field (0x18 = Speed Control)

For 750-671: Must set Application_Selector = 2 and PWM_Period = 0 in WAGO I/O CHECK before using speed control.

For 750-672: Speed control is selected directly via command in Control Byte C1 (no config needed).

Process Image

Both models use 12 bytes bidirectional (96 bits each way):

Input (TxPDO - Controller → PLC):
 [0] S0 (status)
 [1] Reserved
 [2-3] Actual Velocity (i16)
 [4-5] Reserved
 [6-8] Actual Position (24-bit: L, M, H)
 [9] S3 (digital inputs, warnings)
 [10] S2 (busy, error, on_speed, etc.)
 [11] S1 (acknowledgments)

Output (RxPDO - PLC → Controller):
 [0] C0 (control)
 [1] Reserved
 [2-3] Target Velocity (i16, clamped to ±25000)
 [4-5] Acceleration (u16)
 [6-8] Position (24-bit: L, M, H)
 [9] C3 (position/reset control)
 [10] C2 (prescalers, error quit)
 [11] C1 (main control: enable, start, mode)

---

Hardware Quick Reference

Connections

Pin	Name	Purpose
DI1+	Digital Input 1	Enable input (connect to 24V or control via software)
DI2+	Digital Input 2	Referencing input
DI-	Ground	Reference potential for DI1/DI2
A1, A2	Motor Winding A	Connect to motor phase A
B1, B2	Motor Winding B	Connect to motor phase B

Status LEDs

• LED H: Shows error codes via blink patterns (see Wago manual section 3.3 for error codes)
• Other LEDs show Ready, Enable, Busy states (see manual section 2.1.2.3)

---

Architecture & Code Organization

File Structure

devices/
  wago_modules/
    wago_750_672.rs          # Device struct, EtherCAT interface
    
io/
  stepper_velocity_wago_750_672.rs  # High-level wrapper & byte helpers

Key Components

1. Wago750_672 Struct (EtherCAT Device)

Located in devices/wago_modules/wago_750_672.rs

pub struct Wago750_672 {
    is_used: bool,
    tx_bit_offset: usize,  // Input data offset
    rx_bit_offset: usize,  // Output data offset
    pub rxpdo: Wago750_672RxPdo,  // Data we send
    pub txpdo: Wago750_672TxPdo,  // Data we receive
    module: Option<Module>,
    pub state: InitState,
    pub initialized: bool,
}

Responsibilities:

• Implements EtherCAT device traits
• Handles bit-level I/O with process image
• Runs state machine in input() method
• Thread-safe (used via Arc<RwLock<>>)

2. StepperVelocityWago750672 Wrapper

Located in io/stepper_velocity_wago_750_672.rs

pub struct StepperVelocityWago750672 {
    pub device: Arc<RwLock<Wago750_672>>,
    pub state: InitState,
    pub target_velocity: i16,
    pub target_acceleration: u16,
    pub enabled: bool,
    pub freq_range_sel: u8,
    pub acc_range_sel: u8,
}

Responsibilities:

• Provides high-level API (set_velocity(), set_enabled())
• Manages prescaler settings
• Abstracts away state machine complexity

Why Two Layers?

1. Wago750_672: Low-level EtherCAT device that handles cycle-by-cycle I/O
2. StepperVelocityWago750672: High-level wrapper for application logic

This separation allows:

• EtherCAT device to run in tight real-time loop
• Application code to use simple API without worrying about cycles/acknowledgments
• Easy testing of each layer independently

---

Control & Status Bytes

Design Pattern: Type-Safe Byte Construction

Instead of hardcoding hex values like 0x1B, we use builder pattern with enums:

// ❌ BAD - magic numbers, error-prone
dev.rxpdo.c1 = 0x1B;

// ✅ GOOD - explicit, self-documenting
let c1 = ControlByteC1::new()
    .with_flag(C1Flag::Enable)
    .with_flag(C1Flag::Stop2N)
    .with_command(C1Command::SpeedControl)
    .bits();
dev.rxpdo.c1 = c1;

Wago 750-672 Control Bytes

Control Byte C1 (Offset 11) - Main Control

pub struct ControlByteC1(u8);

pub enum C1Flag {
    Enable = 0b0000_0001,  // Bit 0: Must be 1 to enable
    Stop2N = 0b0000_0010,  // Bit 1: Must be 1 for normal operation
    Start  = 0b0000_0100,  // Bit 2: Rising edge triggers action
}

pub enum C1Command {
    Idle          = 0b0000_0000,  // Bits 3-7: Operating mode
    SinglePosition = 0b0000_1000,
    RunProgram    = 0b0001_0000,
    SpeedControl  = 0b0001_1000,  // ← We use this
    Reference     = 0b0010_0000,
    JogMode       = 0b0010_1000,
    Mailbox       = 0b0011_0000,
}

Implementation:

impl ControlByteC1 {
    pub const fn new() -> Self {
        Self(0)
    }

    pub const fn with_flag(mut self, flag: C1Flag) -> Self {
        self.0 |= flag as u8;  // OR in the bit
        self
    }

    pub const fn with_command(mut self, cmd: C1Command) -> Self {
        self.0 = (self.0 & 0b0000_0111) | (cmd as u8);  // Mask lower 3 bits, set upper 5
        self
    }

    pub const fn bits(self) -> u8 {
        self.0
    }
}

Key Points:

• const fn allows compile-time evaluation
• Chainable builder pattern
• Command overwrites bits 3-7 while preserving 0-2
• Flags are additive (multiple can be set)

Control Byte C2 (Offset 10) - Prescalers & Error Handling

pub struct ControlByteC2(u8);

pub enum C2Flag {
    FreqRangeSelL = 0b0000_0001,  // Bit 0: Freq prescaler LSB
    FreqRangeSelH = 0b0000_0010,  // Bit 1: Freq prescaler MSB
    AccRangeSelL  = 0b0000_0100,  // Bit 2: Acc prescaler LSB
    AccRangeSelH  = 0b0000_1000,  // Bit 3: Acc prescaler MSB
    PreCalc       = 0b0100_0000,  // Bit 6: Pre-calculation
    ErrorQuit     = 0b1000_0000,  // Bit 7: Acknowledge error
}

impl ControlByteC2 {
    pub const fn with_freq_range(mut self, sel: u8) -> Self {
        self.0 = (self.0 & 0b1111_1100) | (sel & 0b0000_0011);
        self
    }

    pub const fn with_acc_range(mut self, sel: u8) -> Self {
        self.0 = (self.0 & 0b1111_0011) | ((sel & 0b0000_0011) << 2);
        self
    }
}

Critical: Prescalers can only be changed when controller is disabled (before Enable state).

Control Byte C3 (Offset 9) - Position & Reset

pub struct ControlByteC3(u8);

pub enum C3Flag {
    SetActualPos = 0b0000_0001,  // Bit 0: Set current position
    DirectionPos = 0b0000_0010,  // Bit 2: Force positive direction
    DirectionNeg = 0b0000_0100,  // Bit 3: Force negative direction
    ResetQuit    = 0b1000_0000,  // Bit 7: Acknowledge reset
}

Status Bytes (Read-Only)

Status Byte S1 (Offset 11) - Acknowledgments

pub struct StatusByteS1(u8);

pub enum S1Flag {
    Ready      = 0b0000_0001,  // Bit 0: Acknowledges Enable
    Stop2NAck  = 0b0000_0010,  // Bit 1: Acknowledges Stop2_N
    StartAck   = 0b0000_0100,  // Bit 2: Acknowledges Start
}
// Bits 3-7: Mirrors C1 command when acknowledged

impl StatusByteS1 {
    pub const fn has_flag(self, flag: S1Flag) -> bool {
        (self.0 & flag as u8) != 0
    }
}

Usage Pattern:

// Wait for acknowledgment
if self.txpdo.s1 == c1 {
    // All bits acknowledged, proceed
}

Status Byte S2 (Offset 10) - Operation Status

pub struct StatusByteS2(u8);

pub enum S2Flag {
    OnTarget    = 0b0000_0001,  // Bit 0: Position reached (positioning mode)
    Busy        = 0b0000_0010,  // Bit 1: Executing command
    StandStill  = 0b0000_0100,  // Bit 2: Motor not moving
    OnSpeed     = 0b0000_1000,  // Bit 3: Target velocity reached
    Direction   = 0b0001_0000,  // Bit 4: Rotation direction (0=neg, 1=pos)
    ReferenceOk = 0b0010_0000,  // Bit 5: Referencing complete
    PreCalcAck  = 0b0100_0000,  // Bit 6: Pre-calc acknowledged
    Error       = 0b1000_0000,  // Bit 7: Error occurred (check LED H)
}

Critical for velocity control: Monitor OnSpeed bit to know when target velocity is reached.

Status Byte S3 (Offset 9) - Digital Inputs & Warnings

pub struct StatusByteS3(u8);

pub enum S3Flag {
    Input1  = 0b0000_0001,  // Bits 0-5: Digital input states
    Input2  = 0b0000_0010,
    Input3  = 0b0000_0100,
    Input4  = 0b0000_1000,
    Input5  = 0b0001_0000,
    Input6  = 0b0010_0000,
    Warning = 0b0100_0000,  // Bit 6: Warning condition
    Reset   = 0b1000_0000,  // Bit 7: Reset requested
}

---

Implementation Details

Critical Initialization Sequence

⚠️ This sequence MUST be followed exactly or the controller won't work:

1. Set non-zero acceleration (before enabling)
2. Set Enable + Stop2_N (wait for ack)
3. Set operating mode (0x18 for speed control, wait for ack)
4. Issue Start pulse (set to 1, wait for ack, set to 0, wait for ack clear)
5. Running (repeat step 4 every time velocity changes)

State Machine (Why It Exists)

The state machine exists because acknowledgments happen in different EtherCAT cycles. You can't just set everything in one cycle.

#[derive(Debug, Clone)]
pub enum InitState {
    Off,               // Controller disabled
    Enable,            // Setting Enable + Stop2_N, waiting for ack
    SetMode,           // Setting speed control mode, waiting for ack
    StartPulseStart,   // Setting Start bit, waiting for ack
    StartPulseEnd,     // Clearing Start bit, waiting for ack clear
    Running,           // Normal operation
    ErrorQuit,         // Handling error
    ResetQuit,         // Handling reset
}

State Machine Implementation

Located in Wago750_672::input() method (runs every EtherCAT cycle):

fn input(&mut self, input: &BitSlice) -> Result<(), anyhow::Error> {
    // 1. Read process image from controller
    let base = self.tx_bit_offset;
    let mut b = [0u8; 12];
    for i in 0..12 {
        b[i] = input[base + i * 8..base + (i + 1) * 8].load_le();
    }
    
    self.txpdo = Wago750_672TxPdo {
        s0: b[0],
        actual_velocity: i16::from_le_bytes([b[2], b[3]]),
        position_l: b[6],
        position_m: b[7],
        position_h: b[8],
        s3: b[9],
        s2: b[10],
        s1: b[11],
    };

    // 2. State machine logic
    match self.state {
        InitState::Off => {
            self.initialized = false;
            // Do nothing until external enable request
        }
        
        InitState::Enable => {
            // Build C1 byte with Enable and Stop2_N
            let c1 = ControlByteC1::new()
                .with_flag(C1Flag::Enable)
                .with_flag(C1Flag::Stop2N)
                .bits();
            self.rxpdo.c1 = c1;
            
            // Wait for acknowledgment
            if self.txpdo.s1 == c1 {
                self.state = InitState::SetMode;
            }
        }
        
        InitState::SetMode => {
            // Add speed control command
            let c1 = ControlByteC1::new()
                .with_flag(C1Flag::Enable)
                .with_flag(C1Flag::Stop2N)
                .with_command(C1Command::SpeedControl)
                .bits();
            self.rxpdo.c1 = c1;
            
            // Wait for mode acknowledgment
            if self.txpdo.s1 == c1 {
                self.initialized = true;
                self.state = InitState::StartPulseStart;
            }
        }
        
        InitState::StartPulseStart => {
            // Set Start bit
            let c1 = ControlByteC1::new()
                .with_flag(C1Flag::Enable)
                .with_flag(C1Flag::Stop2N)
                .with_flag(C1Flag::Start)  // ← Rising edge
                .with_command(C1Command::SpeedControl)
                .bits();
            self.rxpdo.c1 = c1;
            
            // Wait for Start acknowledgment
            if self.txpdo.s1 == c1 {
                self.state = InitState::StartPulseEnd;
            }
        }
        
        InitState::StartPulseEnd => {
            // Clear Start bit
            let c1 = ControlByteC1::new()
                .with_flag(C1Flag::Enable)
                .with_flag(C1Flag::Stop2N)
                .with_command(C1Command::SpeedControl)
                .bits();
            self.rxpdo.c1 = c1;
            
            // Wait for acknowledgment to clear
            if self.txpdo.s1 == c1 {
                self.state = InitState::Running;
            }
        }
        
        InitState::Running => {
            // Monitor for errors and resets
            let c2_error_mask = ControlByteC2::new().with_flag(C2Flag::ErrorQuit).bits();
            let c3_reset_mask = ControlByteC3::new().with_flag(C3Flag::ResetQuit).bits();
            
            if self.txpdo.s2 & c2_error_mask != 0 {
                self.state = InitState::ErrorQuit;
            } else if self.txpdo.s3 & c3_reset_mask != 0 {
                self.state = InitState::ResetQuit;
            }
        }
        
        InitState::ErrorQuit => {
            // Set Error_Quit bit to acknowledge
            self.rxpdo.c2 |= ControlByteC2::new().with_flag(C2Flag::ErrorQuit).bits();
            tracing::error!("Stepper Controller Errored. Trying to reenable...");
            self.state = InitState::Enable;  // Restart initialization
        }
        
        InitState::ResetQuit => {
            // Set Reset_Quit bit to acknowledge
            self.rxpdo.c3 |= ControlByteC3::new().with_flag(C3Flag::ResetQuit).bits();
            tracing::error!("Stepper Controller Reset. Trying to reenable...");
            self.state = InitState::Enable;  // Restart initialization
        }
    }
    
    Ok(())
}

Key Implementation Notes:

1. State changes happen AFTER acknowledgment: We wait for self.txpdo.s1 == c1 before moving to next state
2. Enable and Stop2_N stay high: They're included in every C1 byte after Enable state
3. Start pulse is a rising edge: Must go 1 → 0, not just stay at 1
4. Error recovery: Automatically attempts to re-enable on error/reset

High-Level API Implementation

Located in StepperVelocityWago750672:

pub fn set_enabled(&mut self, enabled: bool) {
    // Prevent redundant enables
    if self.enabled && enabled {
        return;
    }
    
    // Safety check: acceleration must be non-zero
    if self.get_target_acceleration() == 0 {
        return;
    }
    
    self.enabled = enabled;
    if enabled {
        self.change_init_state(InitState::Enable);
    } else {
        self.change_init_state(InitState::Off);
        self.write_control_byte(ControlByte::C1, 0b00000000);
    }
}

pub fn set_velocity(&mut self, velocity: i16) {
    self.target_velocity = velocity;
    
    let mut dev = block_on(self.device.write());
    
    // Clamp to valid range
    dev.rxpdo.velocity = velocity.clamp(-25000, 25000);
    
    // Trigger Start pulse if already initialized
    if dev.initialized {
        dev.state = InitState::StartPulseStart;
    }
}

pub fn set_acceleration(&mut self, acceleration: u16) {
    self.target_acceleration = acceleration;
    
    let mut dev = block_on(self.device.write());
    dev.rxpdo.acceleration = acceleration;
}

Why the wrapper?

• Application code doesn't need to know about state machine
• Handles common errors (zero acceleration check)
• Thread-safe access to device
• Clamping and validation in one place

Changing Velocity at Runtime

⚠️ Critical: Must issue a new Start pulse for every velocity change:

// User calls this
stepper.set_velocity(15000);

// Internally, set_velocity() does:
dev.rxpdo.velocity = 15000;
if dev.initialized {
    dev.state = InitState::StartPulseStart;  // ← Triggers new pulse
}

// State machine then handles:
// StartPulseStart → StartPulseEnd → Running
// (Takes 2-3 EtherCAT cycles)

Common mistake: Setting velocity without triggering Start pulse - motor won't change speed.

---

Prescalers & Calculations

Prescalers scale the velocity and acceleration values. They can only be changed when disabled.

Frequency Prescaler (Bits 0-1 of C2)

Controls velocity scaling:

Freq_Range_Sel	Prescaler	Max Frequency	Resolution
00	200 (default)	10 kHz	Configurable
01	80	25 kHz	1 Hz
10	20	100 kHz	20 Hz
11	4	500 kHz	20 Hz

Formula:

Output Frequency (fp) = Velocity × 80 / Freq_Prescaler [Hz]

Example:

// Freq_Range_Sel = 01 (prescaler = 80)
// Velocity = 10000
// Output: 10000 × 80 / 80 = 10000 Hz

stepper.set_freq_range_sel(1);  // Must be done BEFORE enable
stepper.set_velocity(10000);

Acceleration Prescaler (Bits 2-3 of C2)

Controls acceleration scaling:

Acc_Range_Sel	Multiplier	Time to Max Speed
00	8 (default)	7600 ms
01	80	760 ms
10	800	76 ms
11	8000	7.6 ms

Formula:

Acceleration (a) = Acceleration_Value × Acc_Multiplier / Freq_Prescaler [Hz/s]

Example:

// Acc_Range_Sel = 01 (multiplier = 80)
// Freq_Range_Sel = 01 (prescaler = 80)
// Acceleration_Value = 10000
// Output: 10000 × 80 / 80 = 10000 Hz/s

stepper.set_acc_range_sel(1);   // Must be done BEFORE enable
stepper.set_acceleration(10000);

Setting Prescalers (Implementation)

pub fn set_freq_range_sel(&mut self, factor: u8) {
    // Safety checks
    if self.enabled || factor > 3 {
        return;  // Can't change while enabled
    }
    
    self.freq_range_sel = factor;
    
    let mut dev = block_on(self.device.write());
    let c2 = ControlByteC2::from_bits(dev.rxpdo.c2)
        .with_freq_range(factor)
        .bits();
    dev.rxpdo.c2 = c2;
}

pub fn set_acc_range_sel(&mut self, factor: u8) {
    if self.enabled || factor > 3 {
        return;
    }
    
    self.acc_range_sel = factor;
    
    let mut dev = block_on(self.device.write());
    let c2 = ControlByteC2::from_bits(dev.rxpdo.c2)
        .with_acc_range(factor)
        .bits();
    dev.rxpdo.c2 = c2;
}

Usage:

let mut stepper = StepperVelocityWago750672::new(device);

// Set prescalers FIRST (before enabling)
stepper.set_freq_range_sel(1);
stepper.set_acc_range_sel(1);
stepper.set_acceleration(10000);

// Then enable
stepper.set_enabled(true);

// Now can set velocity
stepper.set_velocity(15000);

---

Common Pitfalls & Debug Tips

1. Controller Won't Enable

Symptoms:

• State stuck in Enable
• initialized never becomes true
• Motor doesn't move

Debug checklist:

// Check acceleration is non-zero
println!("Acceleration: {}", dev.rxpdo.acceleration);  // Must be > 0

// Check DI1 if hardware enable is configured
println!("DI1 state: {}", (dev.txpdo.s3 & 0x01) != 0);  // Should be 1

// Check status byte acknowledgment
println!("C1: {:#010b}", dev.rxpdo.c1);
println!("S1: {:#010b}", dev.txpdo.s1);  // Should match C1

Common causes:

// ❌ Forgot to set acceleration
stepper.set_acceleration(0);  // Won't enable!

// ✅ Always set non-zero acceleration
stepper.set_acceleration(10000);
stepper.set_enabled(true);

2. Velocity Won't Change

Symptoms: - Motor running but won't change speed

• set_velocity() called but no effect

Debug:

// Check initialized flag
println!("Initialized: {}", dev.initialized);

// Check state after velocity change
println!("State: {:?}", dev.state);  // Should become StartPulseStart

// Manually trigger Start pulse (bypass wrapper)
dev.state = InitState::StartPulseStart;

Common causes:

// ❌ Setting velocity before initialization
stepper.set_velocity(10000);  // Controller not ready yet

// ✅ Check initialized first
if stepper.device.read().initialized {
    stepper.set_velocity(10000);
}

3. Prescaler Not Working

Symptoms:

• Velocity calculation seems wrong
• Can't reach expected frequency

Debug:

// Check prescalers were set BEFORE enabling
println!("Freq prescaler: {}", stepper.freq_range_sel);
println!("Acc prescaler: {}", stepper.acc_range_sel);
println!("Enabled: {}", stepper.enabled);

// Check C2 byte
let dev = stepper.device.read();
println!("C2: {:#010b}", dev.rxpdo.c2);
// Bits 0-1: freq, Bits 2-3: acc

Common causes:

// ❌ Setting prescaler after enable
stepper.set_enabled(true);
stepper.set_freq_range_sel(1);  // Too late! Ignored.

// ✅ Set prescalers FIRST
stepper.set_freq_range_sel(1);
stepper.set_acc_range_sel(1);
stepper.set_enabled(true);

4. State Machine Stuck

Symptoms:

• State doesn't progress
• Acknowledgments not received

Debug:

// Add logging to state machine
match self.state {
    InitState::Enable => {
        println!("Enable state: C1={:#010b}, S1={:#010b}", self.rxpdo.c1, self.txpdo.s1);
        // ...
    }
}

// Check EtherCAT communication
// - Is cycle running?
// - Are other devices working?
// - Check bus topology

5. Error Bit Set

Symptoms:

• Error bit (S2 bit 7) is 1
• LED H blinking
• Controller stops

Debug:

// Check error state
let s2 = StatusByteS2::from_bits(dev.txpdo.s2);
if s2.has_flag(S2Flag::Error) {
    println!("ERROR DETECTED");
    
    // Count LED H blinks for error code
    // See Wago manual section 3.3
    
    // Check other status flags for clues
    println!("Busy: {}", s2.has_flag(S2Flag::Busy));
    println!("StandStill: {}", s2.has_flag(S2Flag::StandStill));
}

Common error codes:

• 2 blinks: Overcurrent
• 3 blinks: Position error
• 4 blinks: Encoder fault
• See Wago manual for complete list

---

Supporting Wago 750-671

The 750-671 uses different C1 bit layout:

1. Create separate enum:

// For 750-671
pub enum C1Flag671 {
    Enable         = 0b0000_0001,  // Bit 0
    Stop2N         = 0b0000_0010,  // Bit 1
    Start          = 0b0000_0100,  // Bit 2
    MSpeedControl  = 0b0000_1000,  // Bit 3 (instead of command field)
    MProgram       = 0b0001_0000,  // Bit 4
    MReference     = 0b0010_0000,  // Bit 5
    MJog           = 0b0100_0000,  // Bit 6
    MDriveByMBX    = 0b1000_0000,  // Bit 7
}

---

Quick Reference Card

Initialization Checklist

// 1. Create and configure
let stepper = StepperVelocityWago750672::new(device);

// 2. Set prescalers (optional, before enable)
stepper.set_freq_range_sel(1);   // 0-3
stepper.set_acc_range_sel(1);    // 0-3

// 3. Set non-zero acceleration (REQUIRED)
stepper.set_acceleration(10000);

// 4. Enable
stepper.set_enabled(true);

// 5. Set velocity (after initialized)
stepper.set_velocity(15000);     // ±25000 max

Key Constants

const SPEED_CONTROL_CMD: u8 = 0x18;  // C1 command for 750-672
const MAX_VELOCITY: i16 = 25000;
const MIN_VELOCITY: i16 = -25000;
const DEFAULT_ACCELERATION: u16 = 10000;

Critical Rules

1. ⚠️ Never enable with zero acceleration
2. ⚠️ Always wait for acknowledgments
3. ⚠️ Issue Start pulse for every velocity change
4. ⚠️ Prescalers can only be changed when disabled
5. ⚠️ Keep Enable and Stop2_N high during operation

Common Bit Patterns

// Enable + Stop2_N
0b0000_0011

// Enable + Stop2_N + Speed Control
0b0001_1011

// Enable + Stop2_N + Speed Control + Start
0b0001_1111

Debug Commands

# View byte values
println!("C1: {:#010b}", dev.rxpdo.c1);
println!("S1: {:#010b}", dev.txpdo.s1);

# Check specific flags
let s2 = StatusByteS2::from_bits(dev.txpdo.s2);
println!("Error: {}", s2.has_flag(S2Flag::Error));
println!("OnSpeed: {}", s2.has_flag(S2Flag::OnSpeed));

# Monitor state
println!("State: {:?}", dev.state);
println!("Initialized: {}", dev.initialized);

---

Additional Resources

• Wago Manual: Section 2.1.2.3 (LEDs), 3.3 (Error Codes)
• WAGO I/O CHECK: Configuration software for 750-671 application selector
• EtherCAT Specification: www.ethercat.org
• Code Location:
  • Device: devices/wago_modules/wago_750_672.rs
  • Wrapper: io/stepper_velocity_wago_750_672.rs

---

Changelog

Version	Date	Changes
1.0	2025	Initial implementation with state machine
2.0	2026-02	Added comprehensive developer documentation

---

Need help? Check the troubleshooting section or add debug logging using the template above.